|
01-01-2017, 06:05 AM
|
#1
|
3 Rivet Member
2012 25' FB Flying Cloud
Georgetown
, Texas
Join Date: May 2011
Posts: 105
|
How to fix trim pulling away from the wall
Hi all,
Our 2012 25FB has had an issue for a while where the trim pulls away from the wall next to the fridge, usually after traveling over a rough road. I pound it back, it happens again. Only the top part of the trim is separating
I am looking for suggestions for a permanent fix. Thanks in advance!
|
|
|
01-01-2017, 06:12 AM
|
#2
|
Retired.
Currently Looking...
.
, At Large
Join Date: Jun 2003
Posts: 21,276
|
Elmer's wood glue, or Gorilla Glue. The latter would work better, but the trim piece would need to be secured firmly to the bulkhead/wall panel after applying it. Make sure you follow the directions. It would be a good idea to put silicone of something that will hinder whatever you use from sticking to the visible surface before applying either of them.
__________________
Meddle not in the affairs of dragons, for you are crunchy, and taste good with ketchup.
Terry
|
|
|
01-01-2017, 08:38 AM
|
#3
|
Rivet Master
2002 30' Classic S/O
Fleming Island
, Florida
Join Date: Nov 2013
Posts: 4,673
|
I had a similar problem with my Safari 25. I used Gorilla Glue and a brad nailer to hold it until the glue set. The tiny brad holes were largely invisible, but we filled them with a furniture touch-up crayon anyway. My wall was bordered with real oak. If yours is just vinyl covered trim, the vinyl may pull away from the base unless you use some kind or mechanical attachment.
Al
__________________
“You cannot reason someone out of a position they have not been reasoned into"
Al, K5TAN and Missy, N4RGO WBCCI 1322
2002 Classic 30 Slideout -S/OS #004
2013 Dodge 2500 Laramie 4x4 Megacab Cummins
|
|
|
02-05-2017, 01:27 PM
|
#4
|
4 Rivet Member
2017 28' International
Virginia Beach
, Virginia
Join Date: Jul 2016
Posts: 405
|
A little Gorilla Glue and a pin nailer. You won't see the hole.
|
|
|
02-05-2017, 02:04 PM
|
#5
|
Rivet Master
2002 19' Bambi
Lafayette
, California
Join Date: May 2005
Posts: 1,570
|
Gorilla Glue is a wonderful glue, but you should know that its foams up while setting and the foaming glue can squeeze out of the joint for some time after applying the glue. The setup time for Gorilla Glue is about 2 hours, so if you see no foam before that time, you should be okay.
If you see foam coming out, wipe it off immediately. A piece of paper towel wetted with denatured (or isopropyl) alcohol will help in wiping excess off.
It is good idea to wear disposable gloves when working with Gorilla Glue. It can stick to and stain your fingers.
Tim
|
|
|
08-27-2017, 12:51 PM
|
#6
|
3 Rivet Member
2012 25' FB Flying Cloud
Georgetown
, Texas
Join Date: May 2011
Posts: 105
|
Fixed, I think!
Thanks for the replies. I used Gorilla glue and adjustable clamps to hold the trim while the glue dried. I was able to anchor the clamps in an open cabinet and the open fridge (I was careful not to make the ones anchored in the fridge too tight).
Thanks to the warnings about it foaming, I knew to keep checking it until it had totally set. Several times there were small beads of glue the came out of the joint, which I got wiped off before they dried.
The fix has held for about 2,000 miles so far, including on bumpy Oklahoma Interstate highways.
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|