Airstream Forums

Another Small Step

Posted 04-10-2010 at 06:26 PM by Clyde-2

Doesn't look like much, but I reinstalled the water tank and plywood supports. Water level sensors are all working and lights in control panel as well. New pump is roughed in but will wait till kitchen counter assembly is back in place prior to anchoring it. I'm not putting the propane furnace back in so I should have plenty of room under there. NOTE: for any of you out there planning on removing and reinstalling your water tank....use a floor jack to hold it(tank) up then slide the plywood about...

Attached Thumbnails

Click image for larger version

Name: IMG00137.jpg
Views: 343
Size: 590.6 KB
ID: 1490

Clyde-2

2 Rivet Member

Posted in Restoration Blogs, 1972 27' Overlander Restoration

Views 1197 Comments 0 Clyde-2 is offline

Starting Back Up

Posted 04-07-2010 at 05:57 PM by Clyde-2

More pleasant temperatures have re-motivated me(plus I reminded myself what a new one costs) to start back up with the restoration of the Airstream. Last weekend I painted the frame at the wheel wells and the tounge with Rust Bullet. This weekend I will be re-installing the water tank and hooking up the new water pump.

Attached Thumbnails

Click image for larger version

Name: DSC03504.jpg
Views: 268
Size: 386.7 KB
ID: 1481

Click image for larger version

Name: DSC03505.jpg
Views: 271
Size: 305.3 KB
ID: 1482

Clyde-2

2 Rivet Member

Posted in Restoration Blogs, 1972 27' Overlander Restoration

Views 1518 Comments 2 Clyde-2 is offline

More Galley Demo

Posted 11-15-2009 at 04:56 PM by Clyde-2

Continued demolition at the galley. Removed heater. Squirrel cage is completely full of dirt dober nests but still moves freely.

Water pump fires rite up but wouldn't move any water when bench tested. Started trying to disassemble it and the pot metal bolts started breaking. Time for a new quieter one!

All copper looks good, except for one spot where it burst due to freezing I'm sure. All new hoses where needed and should be good to go.

Attached Thumbnails

Click image for larger version

Name: DSC03282.jpg
Views: 264
Size: 447.9 KB
ID: 1097

Click image for larger version

Name: DSC03283.jpg
Views: 268
Size: 294.1 KB
ID: 1098

Click image for larger version

Name: DSC03285.jpg
Views: 266
Size: 252.5 KB
ID: 1099

Click image for larger version

Name: DSC03286.jpg
Views: 290
Size: 236.4 KB
ID: 1100

Clyde-2

2 Rivet Member

Posted in Restoration Blogs, 1972 27' Overlander Restoration

Views 1284 Comments 0 Clyde-2 is offline

Houston....We have Separation

Posted 11-08-2009 at 04:45 PM by Clyde-2

Finally starting to work on the major sytems. Removing galley lower cabinet was not as bad as I thought it would be. Exterior of heater appears to be in good shape. Duct may have to be replaced. Water pump still works when its switch is thrown. Appears water leaks over the years have taken there toll. Most of the flooring will have to be replaced. Fun Fun.

Attached Thumbnails

Click image for larger version

Name: DSC03279.jpg
Views: 294
Size: 358.8 KB
ID: 1083

Click image for larger version

Name: IMG00081.jpg
Views: 289
Size: 508.9 KB
ID: 1084

Click image for larger version

Name: IMG00082.jpg
Views: 281
Size: 440.4 KB
ID: 1085

Clyde-2

2 Rivet Member

Posted in Restoration Blogs, 1972 27' Overlander Restoration

Views 1598 Comments 1 Clyde-2 is offline

Done With Interior Panels !!!!

Posted 11-01-2009 at 04:11 PM by Clyde-2

Finally buffed and installed the last of the interior panels that I am going to remove vinyl from. Decided to do just the front endcap section for now. Also installed the newly painted front screen and window trim sections.

The PO (neighbor) showed up the the original electric jack. He removed it when he parked the trailer 25 years ago. After pulling pulling the motor apart and cleaning it up, it worked !!! Going to need a new rocker switch as it only works in one direction. Don't...

Attached Thumbnails