 dreadydreame
|
Last Activity: 05-18-2009 07:41 PM
About Me
- About dreadydreame
- City
- Newport
- State/Province
- North Carolina
- Country
- UNITED STATES
- Gender
- female
- Trailer #1
- 1965 26' Overlander
Friends
Showing Friends 1 to 3 of 3
-
- danalee
- 4 Rivet Member
-
- jeffreez
- 1 Rivet Member
-
- JuliaPowell
- 1 Rivet Member
Blog
View dreadydreame's BlogRecent Entries
Latest Blog Entry
Posted in
Uncategorized
We got the new black tank from inland installed here is a photo of my husband fiberglassing around the fillings. 
We ended up needing a new thetford valve and new part that the hose attaches to. We got them from vts. We also had to get a new closet flange (toilet floor flange) because the old had the threads rusted off. here is the floor and cut out before we installed black tank.
...
We ended up needing a new thetford valve and new part that the hose attaches to. We got them from vts. We also had to get a new closet flange (toilet floor flange) because the old had the threads rusted off. here is the floor and cut out before we installed black tank.
...
Posted in
Uncategorized
Well it's been a while since I last posted but we are waiting for parts right now.
We got the new toilet from VTS it's a sealand travel lite high toilet. Looks very well made. We tried to use the old floor flange but the threads that go into the black tank were rusted off. So we ordered a new one from VTS (it's on backorder) We looked for a threaded flange everywhere but only found that sealand makes them. We tried to make the old thetford valve work but it was broken and not usable so we...
We got the new toilet from VTS it's a sealand travel lite high toilet. Looks very well made. We tried to use the old floor flange but the threads that go into the black tank were rusted off. So we ordered a new one from VTS (it's on backorder) We looked for a threaded flange everywhere but only found that sealand makes them. We tried to make the old thetford valve work but it was broken and not usable so we...
Posted in
Uncategorized
The fridge is burping right now, and let me tell you it wasn't easy getting it out.
To start out we knew there were 4 bolts in the floor you can see from the outside compartment. We also knew there was an L shaped piece of aluminum on the side that held the counter top to it. We removed the overhead cabinets and the cabinet on top the counter. Then we got the side piece off and the counter up and...
Posted in
Uncategorized
Well we got the new floor in the bathroom. it's a 2 ft section that we had to replace. We went with regular plywood (for floors) We painted it with por 15 to give it some more protection.
Getting it in was not an easy job. We realized it was either try to get it in in one piece by removing the belly skin and getting the skin up high enough to slide it in like some full monti's have done here. or cut in 2 and have a seem somewhere. After starting to remove the belly skin to the right of...
Getting it in was not an easy job. We realized it was either try to get it in in one piece by removing the belly skin and getting the skin up high enough to slide it in like some full monti's have done here. or cut in 2 and have a seem somewhere. After starting to remove the belly skin to the right of...
Posted in
Uncategorized
Since my last update I have painted the frame in the back with por 15 after using marine clean and metal ready on it. We decided to go with regular plywood because the treated wood we bought was a little tiny bit too thick and I read on the forums that the chemicals will eat away at the aluminum. We painted the wood with por 15, and it is cut, we just need to make sure the back end is not leaking at all before we put that in.
...
...
Recent Comments
