|
08-22-2012, 09:19 AM
|
#1
|
2 Rivet Member
1973 29' Ambassador
Mercer Island
, Washington
Join Date: Aug 2012
Posts: 99
|
Another Axle thread (with pics)
Hi,
Looking to buy a 73 29'. Well maintained, but I think original axles. I read the article on inland RV, but it wasn't totally clear to me after crawling under the trailer.
Here is a picture looking from the front of the trailer towards the bach. Ti looks t me like they are shot, but I really can't tell if I'm reading Andy's article backwards.
any thoughts are appreciated so I can negotiate a fair price with the current owner.
|
|
|
08-22-2012, 09:25 AM
|
#2
|
Rivet Master
Airstream Dealer
Corona
, California
Join Date: Feb 2002
Posts: 16,497
|
Quote:
Originally Posted by dcheshire
Hi,
Looking to buy a 73 29'. Well maintained, but I think original axles. I read the article on inland RV, but it wasn't totally clear to me after crawling under the trailer.
Here is a picture looking from the front of the trailer towards the bach. Ti looks t me like they are shot, but I really can't tell if I'm reading Andy's article backwards.
any thoughts are appreciated so I can negotiate a fair price with the current owner.
|
As the torsion arm goes rearward, it should be pointing somwehat down hill.
If it's parallel to the frame, or going uphill as it goes rearward, then the rubber rods within the axle tube have exhausted their life.
Andy
|
|
|
08-22-2012, 10:00 AM
|
#3
|
Rivet Master
1974 Argosy 26
Morrill
, Nebraska
Join Date: Nov 2009
Posts: 6,014
|
There are data plates on the axles with the date of manufacture and the rating of the axle. This will tell you how old the axles are. In looking at your pic, I don't see any down angle. So it's probably time to replace. Figure in the neighborhood of $1500.00 for new axles, if you do the work yourself.
|
|
|
08-22-2012, 10:56 AM
|
#4
|
2 Rivet Member
1973 29' Ambassador
Mercer Island
, Washington
Join Date: Aug 2012
Posts: 99
|
thanks, I'll check the angles and date stamps, but planning for replacement this winter. Hopefully it's OK to get 1-2 trips out of it from now until September and hten i'll call inland and see about getting some new axles, potentially upgrade to discs at the same time
|
|
|
08-22-2012, 11:50 AM
|
#5
|
Retired.
Currently Looking...
.
, At Large
Join Date: Jun 2003
Posts: 21,276
|
The axles probably are bad, but every single Airstream trailer has axles at that angle when new from the factory. The angle at rest proves nothing.
__________________
Meddle not in the affairs of dragons, for you are crunchy, and taste good with ketchup.
Terry
|
|
|
08-22-2012, 12:48 PM
|
#6
|
3 Rivet Member
Commercial Member
1960 24' Tradewind
Riverside
, United States
Join Date: Feb 2007
Posts: 111
|
The designed ride height of a 22 1/2° down start angle is horizontal, scanned from the original Henschen manual.
Greg
__________________
Greg Paulsen
|
|
|
08-22-2012, 01:04 PM
|
#7
|
2 Rivet Member
1973 29' Ambassador
Mercer Island
, Washington
Join Date: Aug 2012
Posts: 99
|
thanks Greg. This graphic would be for the rear axle, so the front axle would be the opposite. I believe that these axles are pointed up, so are shot as the end of the bar that the spindle secures to is actually higher than the frame.
|
|
|
08-22-2012, 02:32 PM
|
#8
|
banjobill
2000 30' Limited
battle ground,
, Washington
Join Date: Jun 2009
Posts: 516
|
huh?
I think it is time to check on the non-responsive domestic, myself.
|
|
|
08-23-2012, 08:41 AM
|
#9
|
Rivet Master
Airstream Dealer
Corona
, California
Join Date: Feb 2002
Posts: 16,497
|
Quote:
Originally Posted by dcheshire
thanks Greg. This graphic would be for the rear axle, so the front axle would be the opposite. I believe that these axles are pointed up, so are shot as the end of the bar that the spindle secures to is actually higher than the frame.
|
Greg's graph, is for "ALL" installed torsion axles on Airstream and Argosy trailers.
There is "no" difference between the fron, center or rear axle, as the case may be.
Andy
|
|
|
09-08-2012, 06:21 AM
|
#10
|
3 Rivet Member
1976 31' Sovereign
Springfield
, South Carolina
Join Date: Jul 2010
Posts: 237
|
My 3200 lb axles are in the neutral loaded angle with no hubs or backing plates at all. Literally unloaded with nothing but spindle and they are still neutral. I used a 6 ton hydraulic jack placed right up under the lift plate and it has about 4 1/2" of life and the tire was still on the ground ! ! ! ! !
Wish I had photographed them from underside before I pulled them off.
|
|
|
09-08-2012, 06:30 AM
|
#11
|
Retired.
Currently Looking...
.
, At Large
Join Date: Jun 2003
Posts: 21,276
|
Quote:
Originally Posted by dcheshire
thanks Greg. This graphic would be for the rear axle, so the front axle would be the opposite. I believe that these axles are pointed up, so are shot as the end of the bar that the spindle secures to is actually higher than the frame.
|
The graphic is for the left trailing arm, so the right would be the opposite.
__________________
Meddle not in the affairs of dragons, for you are crunchy, and taste good with ketchup.
Terry
|
|
|
09-08-2012, 08:13 AM
|
#12
|
Rivet Master
Airstream Dealer
Corona
, California
Join Date: Feb 2002
Posts: 16,497
|
Quote:
Originally Posted by Hummer
My 3200 lb axles are in the neutral loaded angle with no hubs or backing plates at all. Literally unloaded with nothing but spindle and they are still neutral. I used a 6 ton hydraulic jack placed right up under the lift plate and it has about 4 1/2" of life and the tire was still on the ground ! ! ! ! !
Wish I had photographed them from underside before I pulled them off.
|
Your measurements say that the rubber rods are worn out.
That means the trailer will bottom out when hitting bumps, no exceptions.
Andy
|
|
|
09-08-2012, 08:16 AM
|
#13
|
Restorations done right
Commercial Member
1962 26' Overlander
1961 26' Overlander
Vintage Kin Owner
Currently Looking...
Baltimore
, Maryland
Join Date: Aug 2007
Posts: 5,545
|
Quote:
Originally Posted by dcheshire
thanks Greg. This graphic would be for the rear axle, so the front axle would be the opposite. I believe that these axles are pointed up, so are shot as the end of the bar that the spindle secures to is actually higher than the frame.
|
if the front axle is the opposite, you have an axle installed backwards. The arm always trails toward the rear....
|
|
|
09-10-2012, 01:38 PM
|
#14
|
2 Rivet Member
1973 29' Ambassador
Mercer Island
, Washington
Join Date: Aug 2012
Posts: 99
|
Thanks everyone. I bought the trailer and plan on doing the axles this winter (want to order before Andy's summer sale is over). How much time will I save buying the axles "complete" vs reinstalling my brakes onto the new axles. Current brakes/bearings were serviced less than 1 year ago and work great. (looks like $300/axle price difference)
|
|
|
09-11-2012, 06:36 AM
|
#15
|
3 Rivet Member
1976 31' Sovereign
Springfield
, South Carolina
Join Date: Jul 2010
Posts: 237
|
For peace of mind I went with the whole assembly. Went to pick mine up yesterday and they had the mounting brackets welded on backwards. The distribution center manager was not happy. At any rate I took my old axle to do a side by side comparison and he wanted to keep the axle and is going to send it to plant with the bad ones to make sure it is right. Other than that they were beautiful and the hole alignment with AS factory holes was perfect. There were assembled and pre packed with grease ready to bolt up, wire up and go.
I told him I wanted the axle back as I plan on using them to make a car hauler.
|
|
|
09-11-2012, 07:36 AM
|
#16
|
4 Rivet Member
1975 31' Sovereign
Houston
, Texas
Join Date: Nov 2003
Posts: 494
|
Andy, will the hub assembly (or any part of it) transfer from an old Henschen Dura-Torque axle ('74-'80) to a new 'naked' Dexter Torflex axle? [Size # 11 (3600-6000 lb)]
If not, why not?
Hub Assembly = drum, shoes, brake backing plate, brake internal parts.
(did I leave any parts out ?)
thanks
__________________
__________________________
____ d'drummer ____
...aahh..rumm..pu..tum..tummm...
|
|
|
09-12-2012, 09:49 PM
|
#17
|
Rivet Master
Airstream Dealer
Corona
, California
Join Date: Feb 2002
Posts: 16,497
|
Quote:
Originally Posted by Distantdrummer
Andy, will the hub assembly (or any part of it) transfer from an old Henschen Dura-Torque axle ('74-'80) to a new 'naked' Dexter Torflex axle? [Size # 11 (3600-6000 lb)]
If not, why not?
Hub Assembly = drum, shoes, brake backing plate, brake internal parts.
(did I leave any parts out ?)
thanks
|
You left out the bearings.
The old # LM67048 bearing is now a # 15123.
The 25580 bearing remains the same.
But yes, the old drums will fit the new Dexters, but not the never lubes.
Keep in mind however, that the old drums are either 2 or 3 piece and generally way out of balance. New style drums are one piece, machined, and while not perfectly in balance, they still are a vast improvement over the old drums.
Adding the Centramatic balancers to the new drums, takes care of the balancing issues.
Your brakes should be replaced with the new style "self adjusting brakes". Some parts are no longer available for the old style electric brakes.
They are going out the door faster than "hotcakes".
Keeps the brakes adjusted to 100 braking factor, since they continuously adjust themselves, every time you back up the trailer.
Andy
|
|
|
09-12-2012, 10:19 PM
|
#18
|
2 Rivet Member
1974 31' Sovereign
Bend
, Oregon
Join Date: Sep 2009
Posts: 63
|
Andy,
I received my new axles complete with brakes and certramatics from you and installed them last weekend everything fit perfect. I believe they where the 3500# axles with 12 inch brakes.
Thanks again Derf
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|