|
10-27-2006, 04:53 PM
|
#1
|
2 Rivet Member
burbank
, California
Join Date: Jul 2006
Posts: 64
|
removing original rivets
Hello,
I need to take some sheets off my 62 Bambi. It's kinda tricky to drill the heads off the original rivets.
What's the best way of getting the original rivets out?
Thanks,
kamo
|
|
|
10-27-2006, 05:01 PM
|
#2
|
Rivet Master
, Minnesota
Join Date: Aug 2003
Posts: 7,721
|
I use a very sharp drill bit; get one with a split point if you can.
Center the drill bit in the very small dimple in the center of the rivet. You do this more by feel than by sight. I never use a centerpunch or awl.
This next part is the key:
Give the drill chuck about 1/8 to 1/4 turn by hand. This will start curling up a nice chip and seats the bit, although you can't see it. Then start drilling slowly. You can steer the bit a little by using side force if it starts to wander.
Stop drilling when you're through the head, don't go all the way through the stem. If the head doesn't pop off, you can push it off with a putty knife, or even a piece of hard plastic, just be careful not to scratch the AlClad.
Works for me. I drilled at least 500 rivets this way without an accident.
|
|
|
10-27-2006, 05:16 PM
|
#3
|
Retired Moderator
1992 29' Excella
madison
, Wisconsin
Join Date: Aug 2002
Posts: 4,644
|
if you are not going to reuse the sheets a sharp cold chisel will remove them very fast.
john
__________________
you call them ferrets, i call them weasels.
|
|
|
10-27-2006, 05:16 PM
|
#4
|
Silver Mist
Currently Looking...
Riverhead
, New York
Join Date: Aug 2006
Posts: 3,011
|
Great tool
I bought a rivet removal tool from USATCO 53-400 removal tool.
800.645.8180
It centers drills them in and drills them out in about 5 seconds each perfect, it's a got-a-have tool about $30
__________________
Bob
|
|
|
10-27-2006, 06:06 PM
|
#5
|
2 Rivet Member
burbank
, California
Join Date: Jul 2006
Posts: 64
|
Thanks! I'll try to get my hands on the rivet remover. If I can't get it in time, I guess I'll just suffer through it with a sharp drill bit.
Thanks,
kamo
|
|
|
10-27-2006, 06:41 PM
|
#6
|
Silver Mist
Currently Looking...
Riverhead
, New York
Join Date: Aug 2006
Posts: 3,011
|
If you're doing more than a few, I would wait, you can get it by Tuesday.
If you slip just once..............
__________________
Bob
|
|
|
10-27-2006, 08:26 PM
|
#7
|
More than one rivet loose
Currently Looking...
Los Alamos
, New Mexico
Join Date: Feb 2006
Posts: 3,756
|
center punch with an automatic center punch
drill with a small bit until you find the size that is the same as the rivet.
YOu can use that bit for all the rest of the rivets.
You may need numbered drill bits instead of english sizes.
__________________
Michelle TAC MT-0
Sarah, Snowball
Looking for a 1962 Flying Cloud
|
|
|
10-27-2006, 09:57 PM
|
#8
|
Rivet Master
1971 21' Globetrotter
Currently Looking...
Currently Looking...
Currently Looking...
Arvada
, Colorado
Join Date: May 2006
Posts: 3,530
|
Rivet Removel
If the rivets are original they are number 4's or 4/32ths or 1/8". For #4 rivets use a 135 degree split tip #30 drill bit. High speed is best, at least a 2400 RPM drill motor works best. If you are more comfortable, center punch the rivet, then start drilling down the center. the head should pop off on the drill bit. Remove the head from the drill bit tip with pliers (if it did not come off the drill bit by its self)and drill out the shank. Same procedure if the rivets are #5's or 5/32" only use a #21 drill bit. If the rivets are #6 or 6/32 or 3/16th's use a #10 drill bit. If you are not sure what size they are, start with the #30 bit and step up to a #21 if the head does not drill off with with the #30. You should not have to go to the #10 but who knows. After you have drilled off a few it becomes much easier. Good Luck
Kip
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|