Reply
 
Thread Tools Search this Thread Display Modes
 
Old 01-03-2017, 07:49 PM   #29
Rivet Master
 
Waipio Rim's Avatar

 
1984 31' Airstream310
Honokaa , Hawaii
Join Date: Jun 2010
Posts: 832
Quote:
Originally Posted by image360 View Post

I'm still looking for the Owners packet with no luck but this new PDF at least appears to provide a lot of info on the engine, drive train, etc side of these silver wonders.

Robert
If you are looking for the owner's manual, there is a link at post #49 on this thread: http://www.airforums.com/forums/f311...ead-95034.html
__________________

Waipio Rim is offline   Reply With Quote
Old 01-04-2017, 03:34 PM   #30
Rivet Master
 
Boom Sounds's Avatar
 
1991 25' Airstream 250
Oxford , Oxfordshire
Join Date: Jun 2007
Posts: 953
Images: 5
Here


http://www.gmcmi.com/wp-content/uplo...sis-Manual.pdf
http://www.73-87chevytrucks.com/tech...ice_Manual.pdf
http://www.73-87chevytrucks.com/tech...air_Manual.pdf
http://www.73-87chevytrucks.com/tech...iveability.pdf
http://www.73-87chevytrucks.com/tech...10_30_Only.pdf

Mirrors are probably Ramco or Remco (can't recall)


Sent from my iPhone using Airstream Forums
__________________

Boom Sounds is offline   Reply With Quote
Old 01-04-2017, 03:54 PM   #31
Rivet Master
 
Boom Sounds's Avatar
 
1991 25' Airstream 250
Oxford , Oxfordshire
Join Date: Jun 2007
Posts: 953
Images: 5
Btw Robert - if you swap out your old mirrors for entirely new ones, would you be amenable to keeping the old ones so that I can repair part of mine? I'd be happy to pay a modest fee. PM me if you decide to go down that route.

Thanks


Sent from my iPhone using Airstream Forums
Boom Sounds is offline   Reply With Quote
Old 01-16-2017, 04:53 PM   #32
2 Rivet Member
 
Austin , Texas
Join Date: May 2016
Posts: 71
It's looks like Ramco for mirrors

Thanks Boom Sounds,

It looks like the mirrors were Ramco, in contact with them. And yes, will keep yopu in mind if I do replace them, trying to see if I can just replace the shell and attachment.

Thanks,

Robert
image360 is offline   Reply With Quote
Old 01-29-2017, 03:49 PM   #33
2 Rivet Member
 
Austin , Texas
Join Date: May 2016
Posts: 71
Hydralic Power Levelers work!

I'm lucky to have the deluxe hydraulic levelers on my coach. Finally tested them today after I found full instructions on how to operate them and that if by chance the oil and power failed after they are down you can easily baring them back up manually. And they worked!
image360 is offline   Reply With Quote
Old 01-30-2017, 03:47 PM   #34
3 Rivet Member
 
1988 32.5' Airstream 325
calgary , alberta
Join Date: Dec 2006
Posts: 122
Hey Robert how are you? Can you send me a picture of your hydraulic levelers and one of the inside controllers? Hope all is well Jonathan
jhenry is offline   Reply With Quote
Old 02-01-2017, 04:00 PM   #35
2 Rivet Member
 
Austin , Texas
Join Date: May 2016
Posts: 71
Pictures of Hydrolic leveler system

Here's a pic of the back two levelers in the up position, notice the spring for retracting.

Well the picture did not show up, it seems I have no idea how to get pictures to this site, it was a small png image only about 1290 by 960 pixels.

If you really want to see pictures of this, send me a PM with your email.
image360 is offline   Reply With Quote
Old 02-01-2017, 04:19 PM   #36
3 Rivet Member
 
1988 32.5' Airstream 325
calgary , alberta
Join Date: Dec 2006
Posts: 122
Robert my email still same jhf@firmcanada.com thanks Jonathan
jhenry is offline   Reply With Quote
Old 02-10-2017, 05:14 PM   #37
2 Rivet Member
 
Austin , Texas
Join Date: May 2016
Posts: 71
hey boom sounds, just ordered new mirrors, what parts are you looking for from the old ones?

Robert
image360 is offline   Reply With Quote
Old 02-10-2017, 05:25 PM   #38
2 Rivet Member
 
Austin , Texas
Join Date: May 2016
Posts: 71
Update 02/2017

Getting new mirrors from Ramco, replacing old 1002 models with 1302 models or something like that. New roof fans, gas gauge, stereo, dish to HD antenna, rebuild generator, new gas lines, and many other system test.
Also new contractor Stephen OShoney



going to work on lots of things perhaps.
image360 is offline   Reply With Quote
Old 02-12-2017, 10:59 AM   #39
Rivet Master
 
Boom Sounds's Avatar
 
1991 25' Airstream 250
Oxford , Oxfordshire
Join Date: Jun 2007
Posts: 953
Images: 5
Quote:
Originally Posted by image360 View Post
Getting new mirrors from Ramco, replacing old 1002 models with 1302 models or something like that. New roof fans, gas gauge, stereo, dish to HD antenna, rebuild generator, new gas lines, and many other system test.
Also new contractor Stephen OShoney



going to work on lots of things perhaps.

Please don't chuck the old mirrors as I would love to salvage a couple of bits if they are available, especially lower glass on drivers side (mine is smashed) and the tiny Allen screws.

Please PM if possible

All the best
Nick and Helen

All the best
Nick


Sent from my iPhone using Airstream Forums
Boom Sounds is offline   Reply With Quote
Old 09-04-2017, 05:02 PM   #40
2 Rivet Member
 
Austin , Texas
Join Date: May 2016
Posts: 71
After a long pause I'm getting things done again. Two new top fans and front seam leak fixed. New mirrors on outside and new power 30 amp plug after issue with over heating this very hot summer in Austin. Also new stereo/GPS/Backupcamera being installed. Long list of things to come. Budget is not unlimited.
image360 is offline   Reply With Quote
Old 09-04-2017, 06:00 PM   #41
3 Rivet Member
 
Grosspoluter's Avatar
 
1984 34.5' Airstream 345
Franklin Park , Illinois
Join Date: Jan 2015
Posts: 172
Quote:
Originally Posted by image360 View Post
After a long pause I'm getting things done again. Two new top fans and front seam leak fixed. New mirrors on outside and new power 30 amp plug after issue with over heating this very hot summer in Austin. Also new stereo/GPS/Backupcamera being installed. Long list of things to come. Budget is not unlimited.


I understand the budget thing
I'd love to pat ya on the back and give you an "at-a-boy"
God knows I feel your pain
(I have to figure out how to get a positive camber back on my 345's tag axel)
At what point does one jus throw up his hands and say "I quit" ?
I haven't got there... yet
But congratulations on making more progress again
Grosspoluter is offline   Reply With Quote
Old 08-17-2018, 04:31 PM   #42
2 Rivet Member
 
Austin , Texas
Join Date: May 2016
Posts: 71
Back on track maintenace/repairs.

We'll my coach is finally off from a 1.5 year or so visit to Elgin, TX. Helping a old friend out as she gutted her old farmhouse and lived in the RV until a couple of weeks ago.



Unfortunately, it failed inspection, pulling to the left and then the starter motor along with a few other items associated with starting failed. So it's now out at DIY in Roundrock waiting to be serviced with the starter stuff and remaining suspension items along with perhaps a few other under body things.



Next up, hard to say.
__________________

image360 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
master cylinder for 1988 325 jhenry Classic Motorhomes 1 03-03-2015 05:43 PM
1988 Airstream 325 - Texas Jetstreamer Airstream Classifieds 0 04-05-2014 06:24 PM
1988 AIRSTREAM 325 Motorhome eBay Watch Airstreams on eBay 0 01-26-2014 02:10 PM
1988 325 motor home sliding windows Howell General Motorhome Topics 0 04-21-2006 03:18 PM


Featured Campgrounds

Reviews provided by

Disclaimer:

This website is not affiliated with or endorsed by the Airstream, Inc. or any of its affiliates. Airstream is a registered trademark of Airstream Inc. All rights reserved. Airstream trademark used under license to Social Knowledge LLC.




Copyright 2002- Social Knowledge, LLC All Rights Reserved.

All times are GMT -6. The time now is 04:34 PM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.